These tools can help the community define, elaborate, and provide specificity when using the term active learning to characterize teaching practices.To excel in modern science, technology, engineering, and mathematics careers, biology majors need a range of transferable skills, yet competency development is often a relatively underdeveloped facet of the undergraduate curriculum. We have elaborated the Vision and Change core competency framework into a resource called the BioSkills Guide, a set of measurable learning outcomes that can be more readily implemented by faculty. Following an iterative review process including more than 200 educators, we gathered evidence of the BioSkills Guide's content validity using a national survey of more than 400 educators. Rates of respondent support were high (74.3-99.6%) across the 77 outcomes in the final draft. Our national sample during the development and validation phases included college biology educators representing more than 250 institutions, including 73 community colleges, and a range of course levels and biology subdisciplines. Comparison of the BioSkills Guide with other science competency frameworks reveals significant overlap but some gaps and ambiguities. These differences may reflect areas where understandings of competencies are still evolving in the undergraduate biology community, warranting future research. We envision the BioSkills Guide supporting a variety of applications in undergraduate biology, including backward design of individual lessons and courses, competency assessment development, and curriculum mapping and planning.The traditional workflow for biological dosimetry based on manual scoring of dicentric chromosomes is very time consuming. Especially for large-scale scenarios or for low-dose exposures, high cell numbers have to be analyzed, requiring alternative scoring strategies. Semi-automatic scoring of dicentric chromosomes provides an opportunity to speed up the standard workflow of biological dosimetry. Due to automatic metaphase and chromosome detection, the number of counted chromosomes per metaphase is variable. This can potentially introduce overdispersion and statistical methods for conventional, manual scoring might not be applicable to data obtained by automatic scoring of dicentric chromosomes, potentially resulting in biased dose estimates and underestimated uncertainties. The identification of sources for overdispersion enables the development of methods appropriately accounting for increased dispersion levels.
Calibration curves based on invitro irradiated (137-Cs; 0.44?Gy/min) blood from three healthynting for overdispersion introduced by variations in the number of detected chromosomes were developed, enabling more robust dose estimation and quantification of uncertainties for semi-automatic counting of dicentric chromosomes.The PETACC 6 trial investigates whether the addition of oxaliplatin to preoperative capecitabine-based chemoradiation and postoperative capecitabine improves disease-free survival (DFS) in locally advanced rectal cancer.
Between November 2008 and September 2011, patients with rectal adenocarcinoma within 12 cm from the anal verge, T3/4 and/or node positive, were randomly assigned to 5 weeks preoperative capecitabine-based chemoradiation (45-50.4 Gy) followed by six cycles of adjuvant capecitabine, both without (control arm, 1) or with (experimental arm, 2) oxaliplatin. The primary end point was improvement of 3-year DFS by oxaliplatin from 65% to 72% (hazard ratio [HR], 0.763).
A total of 1,094 patients were randomly assigned (intention to treat), and 1,068 eligible patients started their allocated treatment (arm 1, 543; arm 2, 525), with completion of protocol treatment in 68% (arm 1) 54% (arm 2). A higher rate of grade 3/4 adverse events was reported in the experimental arm (14.4% 37.3% and 23.4ine-based chemoradiation and postoperative adjuvant chemotherapy impairs tolerability and feasibility and does not improve efficacy.Little is known about the life course prevalence of bullying among university students. The current study examined the prevalence of bullying in different life periods among multi-university students. Our study included 4,034 university students from four types of universities. Participants self-reported four types of bullying (i.e., physical, verbal, relational, and cyber) with bullies and victims, and four periods (i.e., primary school or earlier, middle school, high school, and postsecondary education). Overall, the percentage of university students experiencing at least one type of bullying victimization (BV) and bullying perpetration (BP) during their lifetime was 59.7% and 31.6%, respectively; the percentage of the university students experiencing more than two types of BV and BP was 16.3% and 7.4%, respectively. The prevalence rates of each type of BV and BP were the highest in elementary school or earlier, and these rates decreased from elementary school or earlier to postsecondary education period. Four latent classes were identified for BV low BV (73.8%), moderate BV (18.6%), secondary school BV (4.4%), and persistent BV (3.2%). Similarly, four classes for BP were identified low BP (86.6%), primary school BP (8.1%), high school BP (1.5%), and persistent BP (3.8%). These findings may inform school health practice of bullying prevention by taking prevention programs, especially during elementary school or earlier period.Electrostatic film actuators represent a promising new approach to drive a soft robot, but they lack a comprehensive model to link the design parameters and actuation performance, making actuator design and parameter optimization challenging. To solve this problem, we build a mathematical model based on the method of moments by assuming that each electrode consists of a large number of line charges. This model can directly deduce fluctuation in thrust and adhesive forces during actuator movement, as well as the distribution of electric potential and field strength, for analysis and optimization. It consumes shorter computing time and fewer computing resources, but with comparable accuracy, in comparison with previous indirect means. It is validated by results from both previous studies and on-site experiments. https://www.selleckchem.com/products/wp1066.html Based on this model, we generate numerous values of actuator output force for different structural parameters. By analyzing the tendency, we summarize a parameter optimization workflow and write an open-sourced program as an example to facilitate the parameter selection for actuator design starting from scratch.